Motorcycle Ignition Switch/electric door/Seat Lock Keys Set for Dayang 100DY100
Product categories
- ATV Parts (10835)
- Bicycle Parts (491)
- Camshaft (248)
- Car Parts (2229)
- Clutch (2330)
- Clutch Accessories (1301)
- Clutch Kits (92)
- Drive Clutch (486)
- Driven Clutch (451)
- CV Axles (8)
- Dirt Bike Parts (27)
- Drift trike Parts (6)
- Garden Parts (4)
- Go Kart Parts (657)
- Golf Cart Parts (5361)
- Lawn Mower Parts (9533)
- Minibike Parts (1158)
- Motorboat Parts (448)
- Motorcycle Parts (3894)
- harley motorcycle (1192)
- Mower Accessories (13)
- OEM Parts (162)
- OIL COOLER (68)
- Other Parts (1701)
- Scooter Parts (896)
- Snowmobile and Snow Blower Parts (455)
- Tractor and Trailer and Truck Parts (2785)
- UTV Parts (2047)
Product tags
Motorcycle Ignition Switch/electric door/Seat Lock Keys Set for Dayang 100DY100
Motorcycle Ignition Switch/electric door/Seat Lock Keys Set for Dayang 100DY100
Post date
April 27, 2024 - Updated on April 27, 2024
Description
??Step 1 ?C Position the Motorcycle??
Park your motorcycle on a flat, level surface with ample lighting nearby. Ideally, set up outdoors if the weather is clear or indoors with a lot of windows or bright lights. Be sure to have your tools close by.
??Step 2 ?C Disconnect the Battery??
Before going any further with removing the ignition switch, you??ll need to disconnect your battery. Remove your rider??s seat to access the ignition area of your motorcycle and set it aside. Always start by removing the negative terminal wire lead before the positive terminal wire lead, never positive before negative or you could burnout or short circuit the battery.
??Step 3 ?C Loosen the Pinch Bolts??
Loosen the two Allen head, pinch bolts that hold the upper triple tree to the front forks. This is also the large bracket directly above the handlebars.
??Step 4 – Remove the Damper??
Remove steering damper next if your motorcycle has one. Unscrew the bolts that hold it up on the upper triple tree, but leave the opposite end of the steering damper attached to the frame. Simply just pivot it opposite the triple tree to move on.
??Step 5 – Remove the Triple Tree??
Remove the 32 mm nut and washer that hold the upper triple tree to the steering stem, and then pull the upper triple tree and off the stem and fork.
Then, trace the original wiring until you locate the connector in your motorcycle. Disconnect the connector by separating the ignition from its wiring harness.
Now you can remove the entire upper triple tree and ignition switch from your motorcycle and lay it down on a wide table. Make sure this area is free of clutter so you do not lose any small parts. It also helps to lay a white towel or sheet on the surface so any loose parts will stand out and be easy to see.
??Step 6 ?C Remove the Ignition Switch??
Set ignition switch facing down and locate the two bolts that hold it to the underside of the triple tree. The ignition switch may be secured with either one-time use bolts or hex head bolts, but either way it must be removed with a bolt extractor tool.
Gently remove the ignition switch from the upper triple clamp. Finally, you can replace your old ignition switch with a new set and reverse these steps to re-install the device.
Contact Us
Related products
-
Tractor and Trailer and Truck Parts
8N2200B Set 4 Brake Shoes Fits Ford Tractor NAA Jubilee 8N Drum Type
-
Tractor and Trailer and Truck Parts
NCA2218B Brake Shoe Sold 4/Box Drum Fits Ford New Holland 2000 4000 600 Ser
-
Tractor and Trailer and Truck Parts
E-8N2200B Drum Type Brake Shoe Fits Ford/New Holland 8N NAA (4 Pcs)